Clopay garage door bottom seal at North Shore Commercial Door, this proprietary replacement bottom rubber weather seal is for use with Clopay garage doors only. Clopay Authorized Dealer - YOUR SINGLE SOURCE - Residential & Commercial N/NW Chicago and suburbs. We know that Clopay has many styles and choices for their garage doors. If you want professional assistance please contact us (see above) for prompt and knowledgeable service which will probably exceed your expectations.
PreamblePlease note, the original article was written on year 2011, which is more than 5 years ago, a lot of things has changed (for example, rolling code are used more and more in today’s market), so we decided to write a small guide to explain the remotes that fit steps below.In the original article below, you can see we have explained two steps to clone garage door remotes, these steps are under the following conditions.1. The original remote you have, should be fixed code remotes (which means there’re likely dip switches on remotes, especially when those dip switches are to control the address code of remote controls), the typical remotes fit this description are Linear Multicode 300/310, Came Top432na etc.2. You should have aftermarket remotes with cloning capabilities (they’re usually called, cloning remotes, cloner, self-learning remote, remote control duplicator, duplicating remotes etc), they need to have this self-learning feature to learn code from your existing remotes.If your original remotes & newer remotes meet above description, then please read on.Otherwise, you might need to contact your seller, or please leave a comment at end of this article, we will provide some support to help you find the correct remote. Simple 2 Step Programming Instruction Code Clone / Copy / Duplicate Brief Instruction Summary StepKeyfob ActionLED Status1Code ClearPress and hold down buttons A and B on Copy RemoteLED flashes once then flashes quickly2Code ClonePress and hold down corresponding buttons on Copy Remote and Original RemoteLED flashes quicklyCode RecoveryPress and hold down buttons C and D on Copy RemoteLED flashes twice or three times then flashes quicklyNOTE: Code Recovery is not necessary unless you have cleared the code by accident and need to have the previous code restored.
Code ClearPress and hold down buttons A and B on Copy Remote simultaneously, LED flashes once, after approximately 5 seconds, LED on Copy Remote flashes quickly, all the transmitter codes in the memory have now been erased.After code clear, LED will flash once and remains off when pressing any button on Copy Remote. Code ClonePlace your Original Remote next to Copy Remote. Press and hold down the button on Original Remote that you wish to program onto the corresponding button on Copy Remote, and then press and hold down the corresponding button on Copy Remote. Hold both buttons down until you see LED on Copy Remote flashes quickly. This should only take a few seconds, and then you have successfully duplicated the code from Original Remote.Repeat the above code clone procedure for buttons B, C and D on Copy Remote if required.After successfully learned, LED will turn on and remains on when any button on Copy Remote is pressed, and the button on Copy Remote will function the same as Original Remote, the clone procedure is now complete. Code Recovery – OptionalIf you have cleared the code by accident, press and hold down buttons C and D on Copy Remote simultaneously, after approximately 5 seconds, LED on Copy Remote flashes twice or three times, then flashes quickly, all the transmitter codes in memory have now been recovered.
![Clop garage door model 4310 Clop garage door model 4310](/uploads/1/2/5/4/125430060/535890858.webp)
Prerequisites & TipsIf you have followed exactly the above programming procedure, but the Copy Remote does not work with your garage door opener, there are basically two major factors to consider: Firstly, your existing remote control might not be fixed code type. Secondly, your existing remote control and Copy Remote must transmit signal on the same frequency. The frequency is factory preset to 315MHz which is the standard for radio remote control apparatus in USA and China.
Nick and Dan Janesko have been operating J&J Garage Doors since 2016. With a combined 6 years of experience, they offer prompt, professional service at fair prices. Their services include sales, installation, and repair of garage doors and openers for commercial and residential projects. J&J is fully insured, licensed, and offer free estimates on all jobs.
![Clop Garage Door Model 4310 Clop Garage Door Model 4310](/uploads/1/2/5/4/125430060/472191229.webp)
Based out of Smithfield, PA, they service Pennsylvania and West Virginia. Call them today at 724-562-9170 to get started!Why choose J&J Garage Doors?.
Provides quick and professional service. Commercial and residential. Fully insured and licensed. Deals direct with DC centers for doors.
Fair pricing. Free estimates.